{"id":2907,"date":"2026-02-02T06:21:16","date_gmt":"2026-02-02T06:21:16","guid":{"rendered":"https:\/\/xbrele.com\/?p=2907"},"modified":"2026-10-14T12:57:42","modified_gmt":"2026-10-14T12:57:42","slug":"ct-accuracy-classes-metering-protection-guide","status":"publish","type":"post","link":"https:\/\/xbrele.com\/it\/ct-accuracy-classes-metering-protection-guide\/","title":{"rendered":"Classi di precisione dei trasformatori di corrente (CT) (0,2\/0,5, 5P\/10P): Misurazione e protezione"},"content":{"rendered":"<p class=\"xbrele-article-updated\"><small>Ultimo aggiornamento: <time datetime=\"2026-10-14\">October 14, 2026<\/time>.<\/small><\/p>\n\n\n\n<p>Current transformers supply measuring instruments and protection relays with scaled current signals. Metering classes describe measurement accuracy over a specified load-current range; protection classes describe performance under the fault conditions covered by their designation. A metering-class label alone does not establish suitability for protection, and a protection-class label alone does not establish revenue-metering accuracy.<\/p>\n\n\n\n<p>Questa guida analizza le denominazioni delle classi di precisione IEC 61869-2, spiega le differenze tecniche tra le classi di misurazione (0,1, 0,2, 0,5) e le classi di protezione (5P, 10P) e fornisce una guida pratica alla scelta per le applicazioni in media tensione.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"what-are-ct-accuracy-classes\">Cosa sono le classi di precisione della TC?<\/h2>\n\n\n\n<p>A CT accuracy class defines permissible errors under specified current, burden, frequency and test conditions. For a metering CT, the class number identifies the rated-current ratio-error limit; other test currents have their own limits. In a 5P or 10P designation, the number identifies the composite-error limit at the rated accuracy-limit primary current, not the ratio-error limit at normal load.<\/p>\n\n\n\n<p>Esistono due sistemi di classificazione distinti. Le classi di misurazione (0,1, 0,2, 0,5, 1,0) ottimizzano la precisione per le normali correnti di funzionamento, tipicamente da 5% a 120% della corrente nominale. Le classi di protezione (5P, 10P) danno priorit\u00e0 alle prestazioni in condizioni di guasto, mantenendo la precisione a multipli di corrente molto superiori al normale funzionamento.<\/p>\n\n\n\n<p>Metering and protection impose different design requirements. A CT may contain separate metering and protection cores, and some designs carry more than one accuracy designation. Select each core using its declared ratings and the connected equipment requirements; neither core size nor material alone proves its accuracy class.<\/p>\n\n\n\n<figure class=\"wp-block-embed is-type-video is-provider-youtube wp-block-embed-youtube wp-embed-aspect-16-9 wp-has-aspect-ratio\"><div class=\"wp-block-embed__wrapper\">\n<iframe title=\"Classi di precisione dei TA spiegate: Misurazione 0,2\/0,5 vs Protezione 5P\/10P\" width=\"1290\" height=\"726\" src=\"https:\/\/www.youtube.com\/embed\/PVXlrxYOFzA?feature=oembed\" frameborder=\"0\" allow=\"accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture; web-share\" referrerpolicy=\"strict-origin-when-cross-origin\" allowfullscreen><\/iframe>\n<\/div><\/figure>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"how-current-transformers-introduce-measurement-errors\">Come i trasformatori di corrente introducono errori di misura<\/h2>\n\n\n\n<p>Part of the primary ampere-turns supplies the core excitation rather than the secondary load. The resulting exciting current, together with the secondary circuit impedance, produces ratio error and phase displacement.<\/p>\n\n\n\n<p><strong>Errore di rapporto (\u03b5)<\/strong> is the difference between the primary current inferred from the rated ratio and the actual primary current, expressed as a percentage of the actual primary current. With a rated ratio of 1000\/5 A, a secondary reading of 4.98 A at 1000 A primary gives (200 \u00d7 4.98 \u2212 1000) \/ 1000 \u00d7 100 = \u22120.4%. The error varies with current and burden.<\/p>\n\n\n\n<p><strong>Spostamento di fase (\u03b4)<\/strong>&nbsp;misura la differenza angolare tra i fasori della corrente primaria e secondaria, espressa in minuti d'arco. La trasformazione ideale produce uno sfasamento nullo; i TA reali presentano piccoli spostamenti dovuti ai requisiti della corrente di magnetizzazione.<\/p>\n\n\n\n<p>Core material, geometry, turns and excitation characteristics all influence CT performance. Rated output is stated in VA at the rated secondary current. Check the manufacturer\u2019s declared burden range and burden power factor as well as the VA rating: a very small connected burden is not automatically within the metering accuracy guarantee.<\/p>\n\n\n\n<p>The limits apply at the current and burden conditions specified for the class. At rated primary current, Class 0.2 has ratio-error and phase-displacement limits of \u00b10.2% and \u00b110 minutes. For protection classes, the rated-current ratio-error limits are \u00b11% for 5P and \u00b13% for 10P; their respective composite-error limits at the rated accuracy-limit current are 5% and 10%.<\/p>\n\n\n\n\n\n<h2 class=\"wp-block-heading\" id=\"metering-ct-accuracy-classes-0.1-0.2-0.5-and-extended-s-classes\">Classi di precisione del TA di misurazione: 0.1, 0.2, 0.5 e classi \u201cS\u201d estese<\/h2>\n\n\n\n<p>Metering classes specify ratio-error and phase-displacement limits at several test currents. The table lists the limits at 100% rated current and the covered current range. It does not mean that the rated-current error limit applies unchanged over that entire range; use the full class table and the CT\u2019s declared burden conditions for selection.<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table class=\"has-fixed-layout\"><thead><tr><th>Classe<\/th><th>Errore di rapporto a 100% In<\/th><th>Phase displacement at 100% In<\/th><th>Specified current range<\/th><th>Applicazione tipica<\/th><\/tr><\/thead><tbody><tr><td>0.1<\/td><td>\u00b10,1%<\/td><td>\u00b15 min<\/td><td>5-120%<\/td><td>Standard di riferimento per il laboratorio<\/td><\/tr><tr><td>0.2<\/td><td>\u00b10,2%<\/td><td>\u00b110 min<\/td><td>5-120%<\/td><td>Misurazione dei ricavi di trasmissione<\/td><\/tr><tr><td>0.2S<\/td><td>\u00b10,2%<\/td><td>\u00b110 min<\/td><td>1-120%<\/td><td>Misurazione dei ricavi a carico variabile<\/td><\/tr><tr><td>0.5<\/td><td>\u00b10,5%<\/td><td>\u00b130 min<\/td><td>5-120%<\/td><td>Misurazione della sottostazione di distribuzione<\/td><\/tr><tr><td>0.5S<\/td><td>\u00b10,5%<\/td><td>\u00b130 min<\/td><td>1-120%<\/td><td>Misurazione dei ricavi industriali<\/td><\/tr><tr><td>1.0<\/td><td>\u00b11,0%<\/td><td>\u00b160 min<\/td><td>5-120%<\/td><td>Strumenti indicatori<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<p>The \u201cS\u201d suffix identifies metering classes with additional low-current requirements. Classes 0.2S and 0.5S include a 1% rated-current test point, whereas the ordinary classes listed above start at 5%. Error limits differ by test point. Select a class and ratio that cover the expected minimum load and the applicable metering requirements.<\/p>\n\n\n\n<p>For variable-load facilities, compare the expected minimum primary current with the CT rating before choosing between 0.2 and 0.2S. Billing value alone does not define the required class. Include the meter, voltage measurement and wiring in the overall measurement-accuracy assessment.<\/p>\n\n\n\n<p><strong>Instrument security factor (FS)<\/strong> describes the overcurrent behavior specified for a metering core at rated burden. FS5 and FS10 are common declared ratings, but the accuracy class alone does not prescribe a universal saturation multiple. Reducing the connected burden can increase the current at which the core saturates. Verify FS and the meter\u2019s withstand capability rather than assuming every metering CT saturates at 2\u20135 times rated current.<\/p>\n\n\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<blockquote class=\"wp-block-quote is-layout-flow wp-block-quote-is-layout-flow\">\n<p><strong>Metering CT selection checks<\/strong><\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Compare the expected minimum load with the class test points and the CT ratio.<\/li>\n\n\n\n<li>Verify the complete connected burden is within the CT\u2019s declared metering accuracy range.<\/li>\n\n\n\n<li>Obtain the selected meter\u2019s actual input burden; verify accuracy at the resulting total burden.<\/li>\n\n\n\n<li>Richiedete i certificati dei test di fabbrica che mostrino gli effettivi errori misurati, non solo la conformit\u00e0 alla classe.<\/li>\n<\/ul>\n<\/blockquote>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"protection-ct-accuracy-classes-decoding-5p-and-10p-designations\">Classi di precisione dei TA di protezione: Decodifica delle designazioni 5P e 10P<\/h2>\n\n\n\n<p>Le classi di protezione seguono un sistema di notazione diverso che riflette la loro funzione principale: la misurazione accurata della corrente di guasto. La designazione \u201c5P20\u201d codifica tre parametri essenziali per il coordinamento dei rel\u00e8.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"nomenclature-breakdown\"><strong>Ripartizione della nomenclatura:<\/strong><\/h3>\n\n\n\n<ul class=\"wp-block-list\">\n<li><strong>5<\/strong>\u00a0= Limite di errore composito (5% massimo)<\/li>\n\n\n\n<li><strong>P<\/strong>\u00a0= Designazione della classe di protezione<\/li>\n\n\n\n<li><strong>20<\/strong> = rated accuracy limit factor at rated burden; the specified composite-error limit is checked at 20 times rated primary current<\/li>\n<\/ul>\n\n\n\n<figure class=\"wp-block-table\"><table class=\"has-fixed-layout\"><thead><tr><th>Classe<\/th><th>Errore composito in ALF<\/th><th>Valori comuni dell'ALF<\/th><th>Applicazione tipica<\/th><\/tr><\/thead><tbody><tr><td>5P<\/td><td>\u22645%<\/td><td>10, 15, 20, 30<\/td><td>Overcurrent protection; verify each relay application<\/td><\/tr><tr><td>10P<\/td><td>\u226410%<\/td><td>10, 15, 20<\/td><td>Overcurrent protection where the scheme accepts 10P<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<p>Il <strong>accuracy limit factor (ALF)<\/strong> is the rated accuracy-limit primary current divided by the rated primary current. A 1000\/5 A, 5P20 CT has a rated accuracy-limit current of 20,000 A at its rated burden. This is a defined steady-state error test condition, not a sharp physical saturation threshold or a guarantee of transient performance.<\/p>\n\n\n\n<p>For a 5P20 CT, the composite error must not exceed 5% at 20 times rated primary current under the specified test conditions and rated burden. Composite error includes waveform distortion and is not a signed \u00b15% ratio-error band. DC offset, remanent flux and the required operating time can impose additional CT requirements.<\/p>\n\n\n\n<p><strong>Initial steady-state screening:<\/strong> if the scheme requires class accuracy at the maximum symmetrical through-fault current, compare the effective ALF at the actual burden with that fault-current multiple.<\/p>\n\n\n\n<p>Required effective ALF \u2265 Maximum symmetrical through-fault current \u00f7 CT rated primary current<\/p>\n\n\n\n<p>For a 12.5 kA symmetrical fault and a 500\/5 A CT, the fault-current multiple is 12,500 \/ 500 = 25.<\/p>\n\n\n\n<p>At rated burden, 5P20 alone does not demonstrate the above 25-times screening requirement; a 5P30 rating would cover that steady-state multiple. Final selection still requires the relay manufacturer\u2019s criteria, actual secondary burden, fault duration and transient assessment. Some protection functions tolerate partial CT saturation, so this screening rule is not a universal relay-sizing formula.<\/p>\n\n\n\n<p>Protection CT selection also involves excitation characteristics, secondary winding resistance and short-time thermal and dynamic ratings. A 5P or 10P designation does not replace these checks. For differential or transient duties, the relay manufacturer may specify PX, PR or a transient class, or give a calculation for an acceptable P-class CT.<\/p>\n\n\n\n\n\n<h2 class=\"wp-block-heading\" id=\"metering-vs-protection-ct-side-by-side-comparison\">TA di misurazione e TA di protezione: un confronto fianco a fianco<\/h2>\n\n\n\n<p>The following comparison summarizes the different performance specifications. Individual CTs can have additional ratings beyond the class names shown.<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table class=\"has-fixed-layout\"><thead><tr><th>Parametro<\/th><th>CT di misurazione<\/th><th>Protezione CT<\/th><\/tr><\/thead><tbody><tr><td><strong>Funzione primaria<\/strong><\/td><td>Fatturazione delle entrate, monitoraggio dell'energia<\/td><td>Rilevamento dei guasti, funzionamento dei rel\u00e8<\/td><\/tr><tr><td><strong>Intervallo di precisione<\/strong><\/td><td>1-120% di nominale (classe S)<\/td><td>Rated error limit at ALF \u00d7 rated current and rated burden<\/td><\/tr><tr><td><strong>Specifiche di errore<\/strong><\/td><td>Errore di rapporto + spostamento di fase<\/td><td>Rated-current ratio error and composite error at ALF<\/td><\/tr><tr><td><strong>Comportamento di saturazione<\/strong><\/td><td>Specified by FS and burden; not by metering class alone<\/td><td>Specified accuracy-limit and transient characteristics<\/td><\/tr><tr><td><strong>Design del nucleo<\/strong><\/td><td>Design depends on accuracy, burden and FS<\/td><td>Design depends on burden, fault and transient duty<\/td><\/tr><tr><td><strong>Classi tipiche<\/strong><\/td><td>0,2, 0,2S, 0,5, 0,5S, 1,0<\/td><td>5P10, 5P20, 10P10, 10P15<\/td><\/tr><tr><td><strong>Dispositivi connessi<\/strong><\/td><td>Contatori di kWh, analizzatori di potenza<\/td><td>Rel\u00e8 di protezione, registratori di guasti<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<p>A saturated CT produces a distorted secondary waveform. Depending on the relay function and settings, this can delay operation or affect differential stability. The magnitude and timing of the effect must be assessed for the actual protection scheme; they cannot be inferred from the metering class alone.<\/p>\n\n\n\n<p>Separate cores allow the metering burden and protection burden to be specified and tested independently when both functions are needed.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"burden-effects-and-practical-selection-considerations\">Effetti dell'onere e considerazioni pratiche sulla selezione<\/h2>\n\n\n\n<p>Connected burden affects the voltage the CT must develop and therefore its accuracy and saturation behavior. Include the relay or meter input and the complete secondary wiring circuit. Keep the metering burden within its declared accuracy range, and calculate protection performance at the actual burden.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"burden-components-include\"><strong>I componenti dell'onere includono:<\/strong><\/h3>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Instrument burden: use the selected meter, relay or transducer input data.<\/li>\n\n\n\n<li>Carico del cavo: resistenza del cavo secondario (significativa per le lunghe tratte)<\/li>\n\n\n\n<li>Connection burden: include terminals and test switches using their actual resistance.<\/li>\n<\/ul>\n\n\n\n<p><strong>Lead burden calculation for a separate outgoing and return pair:<\/strong><br>Lead VA = I<sub>secondary<\/sub>\u00b2 \u00d7 R<sub>loop<\/sub> = I<sub>secondary<\/sub>\u00b2 \u00d7 2 \u00d7 R<sub>one-way<\/sub><\/p>\n\n\n\n<p>Example: a 50 m one-way run with a measured or calculated one-way resistance of 0.35 \u03a9 has a 0.70 \u03a9 loop. At 5 A, its burden is 25 \u00d7 0.70 = 17.5 VA; at 1 A, it is 0.70 VA. Use the cable resistance at the design temperature and the actual return-circuit arrangement.<\/p>\n\n\n\n<p>Questo spiega perch\u00e9 i secondari da 1 A sono adatti a lunghe tratte di cavo: il carico si riduce di 25\u00d7 rispetto ai secondari da 5 A per un cavo identico.<\/p>\n\n\n\n<p><strong>Lista di controllo per la selezione:<\/strong><\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Obtain maximum and minimum fault currents and the relay operating-time requirements.<\/li>\n\n\n\n<li>\u00a0Somma del carico totale, compresa la resistenza degli elettrocateteri<\/li>\n\n\n\n<li>Verify the declared burden conditions for metering and the effective ALF for protection.<\/li>\n\n\n\n<li>Include credible future fault levels and transient duty using the relay manufacturer\u2019s calculation method.<\/li>\n\n\n\n<li>Choose the metering class and ratio to cover the actual load range and project requirements.<\/li>\n<\/ul>\n\n\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<blockquote class=\"wp-block-quote is-layout-flow wp-block-quote-is-layout-flow\">\n<p><strong>Protection CT specification checks<\/strong><\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>For auto-reclosing, assess remanence, fault duration and the required operating cycle.<\/li>\n\n\n\n<li>For differential protection, follow the selected relay\u2019s CT ratio and saturation requirements.<\/li>\n\n\n\n<li>Use the relay\u2019s actual input burden and the complete wiring burden when calculating effective ALF.<\/li>\n\n\n\n<li>Request excitation curves and secondary winding resistance when required by the protection calculation.<\/li>\n<\/ul>\n<\/blockquote>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"dual-core-cts-and-switchgear-integration\">TA a doppio nucleo e integrazione dei quadri elettrici<\/h2>\n\n\n\n<p>La maggior parte degli impianti di media tensione richiede sia la misurazione che la protezione di ciascun alimentatore. I TA bipolari (o multipolari) risolvono questo problema incorporando nuclei magnetici separati avvolti sullo stesso conduttore primario.<\/p>\n\n\n\n<p>Illustrative dual-core specification, subject to the actual meter, relay and wiring calculations:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Nucleo 1: classe 0,5S, carico di 10 VA (misurazione delle entrate)<\/li>\n\n\n\n<li>Nucleo 2: 5P20, carico 30 VA (rel\u00e8 di protezione)<\/li>\n<\/ul>\n\n\n\n<p>Specify and verify the accuracy and burden of each core separately. Confirm metering FS, protection performance, insulation level and the assembly\u2019s thermal and dynamic withstand ratings. Separate cores do not remove the need to coordinate the complete secondary circuits.<\/p>\n\n\n\n<p>Integrazione con <a href=\"https:\/\/xbrele.com\/it\/vacuum-circuit-breaker\/\">interruttori in vuoto di media tensione<\/a> requires a common system fault study. ALF is a dimensionless ratio and cannot be compared directly with a breaker breaking-current rating in kA. Evaluate the CT against the maximum through-fault current, its primary rating, actual burden and relay requirements. Separately verify the CT short-time\/dynamic withstand ratings and the breaker interrupting duty. Ask the <a href=\"https:\/\/xbrele.com\/it\/switchgear-parts\/\">produttori di componenti<\/a> for the data needed to complete those checks.<\/p>\n\n\n\n<p>Quando si specificano i TA per le nuove installazioni, fornire al fornitore quanto segue:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Livello massimo di guasto del sistema (kA)<\/li>\n\n\n\n<li>Intervallo di corrente di carico (da minimo a massimo)<\/li>\n\n\n\n<li>Distanza del cavo dai pannelli di misurazione\/rel\u00e8<\/li>\n\n\n\n<li>Modelli specifici di contatori e rel\u00e8 con dati di carico<\/li>\n<\/ul>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"common-ct-specification-errors-and-how-to-avoid-them\">Errori comuni delle specifiche CT e come evitarli<\/h2>\n\n\n\n<p>Review the following specification errors before purchasing or replacing a CT.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"error-1-using-metering-ct-for-protection\"><strong>Errore 1: Utilizzo del TA di misura per la protezione<\/strong><\/h3>\n\n\n\n<p>A metering class alone does not verify fault-current performance. <strong>Soluzione:<\/strong> select a core with the protection characteristics required by the relay scheme and verify its performance at the actual burden, through-fault current and required operating time.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"error-2-ignoring-lead-burden-in-total-burden-calculation\"><strong>Errore 2: Ignorare il carico di piombo nel calcolo del carico totale<\/strong><\/h3>\n\n\n\n<p>Long secondary circuits can add substantial burden, particularly at 5 A. <strong>Soluzione:<\/strong> calculate the complete loop resistance at the design temperature. Compare 1 A and 5 A options using the actual cable and compatible relay inputs; cable length alone is not a universal selection threshold.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"error-3-mismatched-cts-in-differential-protection\"><strong>Errore 3: TA disadattati nella protezione differenziale<\/strong><\/h3>\n\n\n\n<p>Different saturation behavior can produce unwanted differential current during an external fault. <strong>Soluzione:<\/strong> use the relay manufacturer\u2019s ratio-compensation, excitation, winding-resistance and stability requirements. Transformer differential schemes may use different primary CT ratios; identical ratios and knee-point voltages are not a universal requirement.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"error-4-overlooking-remanent-flux-in-auto-reclose-schemes\"><strong>Errore 4: trascurare il flusso remanente negli schemi di auto-chiusura<\/strong><\/h3>\n\n\n\n<p>Remanent flux can change CT saturation during a subsequent fault or reclosing sequence. <strong>Soluzione:<\/strong> assess the specified operating cycle, system time constant and relay requirements. Select suitable remanence or transient performance where required; a blanket 50% ALF increase is not a verified substitute.<\/p>\n\n\n\n<p>Comprensione <a href=\"https:\/\/xbrele.com\/it\/vacuum-circuit-breaker-ratings\/\">valori nominali degli interruttori automatici sottovuoto<\/a> helps establish the switching duty. CT accuracy selection is a separate calculation based on the actual through-fault duty and protection scheme, while CT thermal\/dynamic withstand must also cover the clearing duty.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"frequently-asked-questions\">Domande frequenti<\/h2>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"what-does-5p20-mean-on-a-current-transformer-nameplate\"><strong>Cosa significa 5P20 sulla targhetta di un trasformatore di corrente?<\/strong><\/h3>\n\n\n\n<p>5P20 specifies a protection CT with a composite-error limit of 5% at a rated accuracy-limit current of 20 times rated primary current, at rated burden and the specified test conditions. For a 400\/5 A CT this test current is 8,000 A. It does not identify an exact saturation threshold or guarantee performance for every transient waveform.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"can-a-0-5-class-metering-ct-feed-protection-relays\"><strong>Un TA di misura di classe 0,5 pu\u00f2 alimentare rel\u00e8 di protezione?<\/strong><\/h3>\n\n\n\n<p>Do not assume that a Class 0.5 metering core is suitable for protection. Its class establishes metering accuracy under specified conditions, not the fault-current performance required by a relay. Use a core whose declared protection characteristics have been checked against the particular relay scheme.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"when-should-i-specify-0-2s-instead-of-standard-0-2-class\"><strong>Quando \u00e8 necessario specificare 0,2S invece della classe standard 0,2?<\/strong><\/h3>\n\n\n\n<p>Consider 0.2S when accurate measurement is required at low load, especially between 1% and 5% of rated CT current. The required class also depends on the utility or project metering specification. Check the limits at each current test point and the declared burden range; 0.2S does not mean \u00b10.2% at every current.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"how-does-burden-affect-protection-ct-performance\"><strong>In che modo l'onere influisce sulle prestazioni del TA di protezione?<\/strong><\/h3>\n\n\n\n<p>A lower external burden generally increases the effective ALF of a P-class CT, but winding resistance must be included. For mainly resistive burdens, ALF<sub>actual<\/sub> \u2248 ALF<sub>valutato<\/sub> \u00d7 (R<sub>ct<\/sub> + R<sub>rated burden<\/sub>) \/ (R<sub>ct<\/sub> + R<sub>actual burden<\/sub>). Therefore, halving external burden does not generally double ALF. Use manufacturer data for the actual circuit and transient duty.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"what-is-knee-point-voltage-and-why-does-it-matter\"><strong>Che cos'\u00e8 la tensione del punto di ginocchio e perch\u00e9 \u00e8 importante?<\/strong><\/h3>\n\n\n\n<p>Knee-point voltage characterizes the bend in the secondary excitation curve. The IEC convention uses the point at which a 10% voltage increase produces a 50% increase in exciting current. It is particularly relevant when specifying PX-type CTs. Apply the relay manufacturer\u2019s knee-point, excitation-current and winding-resistance requirements; a simple voltage comparison does not establish suitability for every protection scheme.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"how-do-iec-and-ieee-ct-accuracy-standards-differ\"><strong>Quali sono le differenze tra gli standard di precisione CT IEC e IEEE?<\/strong><\/h2>\n\n\n\n<p>IEC 61869-2 includes metering classes such as 0.2 and 0.5 and protection classes such as 5P, 10P and PX. IEEE C57.13 uses a different set of designations, including voltage-based relaying classes such as C100 and C200. The test conditions and burden definitions differ. Specify the standard required by the project and compare the full ratings rather than treating the class names as direct equivalents.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"what-accuracy-class-suits-capacitor-bank-switching-applications\"><strong>Quale classe di precisione \u00e8 adatta alle applicazioni di commutazione dei banchi di condensatori?<\/strong><\/h3>\n\n\n\n<p>A capacitor bank can need phase overcurrent, earth-fault and sensitive unbalance protection, each with different measurement duties. Select CT ratio, accuracy, burden and transient performance from the bank configuration, expected unbalance level and relay instructions. A universal 5P10 or 0.5 recommendation cannot establish suitability for all capacitor banks.<\/p>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<p><em>Per un supporto sulle specifiche del TA in base ai requisiti del vostro quadro, contattate il team di ingegneri di XBRELE via <a href=\"https:\/\/xbrele.com\/it\/contact\/\">la pagina dei contatti tecnici<\/a>. Forniamo soluzioni integrate che combinano&nbsp;<a href=\"https:\/\/xbrele.com\/it\/what-is-a-vacuum-interrupter\/\">tecnologia di interruzione del vuoto<\/a>&nbsp;con trasformatori strumentali adeguatamente coordinati per prestazioni di misurazione e protezione affidabili, tra cui <a href=\"https:\/\/xbrele.com\/it\/transformer-protection-vcb-inrush-coordination-mistakes\/\">controlli di coordinamento dei rel\u00e8<\/a> per gli alimentatori dei trasformatori.<\/em><\/p>\n\n\n\n<p><strong>Technical references:<\/strong> <a href=\"https:\/\/webstore.iec.ch\/en\/publication\/6050\" target=\"_blank\" rel=\"noopener\">IEC 61869-2:2012 \u2014 inductive current transformers<\/a>; <a href=\"https:\/\/library.e.abb.com\/public\/194811e319ce2bb7c2256f9e00324a2f\/applicationCT_accuracylimitfactorENa.pdf\" target=\"_blank\" rel=\"noopener\">ABB \u2014 calculation of actual accuracy limit factor<\/a>; <a href=\"https:\/\/library.e.abb.com\/public\/eb71e99b34df40fac2256f230034b639\/applicationCTreqENa.pdf\" target=\"_blank\" rel=\"noopener\">ABB \u2014 CT requirements for non-directional overcurrent protection<\/a>; <a href=\"https:\/\/techdoc.relays.protection-control.abb\/r\/615-series-Technical-Manual\/5.0-FP1-IEC\/en-US\/Current-transformer-requirements-for-transformer-differential-protection?contentId=IOsDImuRMieCseqaGT6Irw\" target=\"_blank\" rel=\"noopener\">ABB \u2014 transformer differential CT requirements<\/a>. The ABB application notes explain calculation methods; final selection must use the applicable project standard and the selected relay\u2019s current instructions.<\/p>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>","protected":false},"excerpt":{"rendered":"<p>Understand CT accuracy classes 0.2S, 0.5S, 5P and 10P, including rated burden, effective ALF and checks for metering and protection applications.<\/p>","protected":false},"author":3,"featured_media":4294,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"_gspb_post_css":"\/* XBRELE: keep the image-free article hero readable. *\/\nbody.postid-2907 #main > .hero-section[data-type=\"type-2\"] {\n  background-color: var(--theme-palette-color-4, #080c0e);\n  --theme-text-color: #e6eef1;\n}\nbody.postid-2907 #main > .hero-section[data-type=\"type-2\"] .page-description {\n  color: var(--theme-text-color);\n}\n","footnotes":""},"categories":[27],"tags":[],"class_list":["post-2907","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-switchgear-parts-knowledge"],"blocksy_meta":[],"_links":{"self":[{"href":"https:\/\/xbrele.com\/it\/wp-json\/wp\/v2\/posts\/2907","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/xbrele.com\/it\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/xbrele.com\/it\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/xbrele.com\/it\/wp-json\/wp\/v2\/users\/3"}],"replies":[{"embeddable":true,"href":"https:\/\/xbrele.com\/it\/wp-json\/wp\/v2\/comments?post=2907"}],"version-history":[{"count":5,"href":"https:\/\/xbrele.com\/it\/wp-json\/wp\/v2\/posts\/2907\/revisions"}],"predecessor-version":[{"id":4291,"href":"https:\/\/xbrele.com\/it\/wp-json\/wp\/v2\/posts\/2907\/revisions\/4291"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/xbrele.com\/it\/wp-json\/wp\/v2\/media\/4294"}],"wp:attachment":[{"href":"https:\/\/xbrele.com\/it\/wp-json\/wp\/v2\/media?parent=2907"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/xbrele.com\/it\/wp-json\/wp\/v2\/categories?post=2907"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/xbrele.com\/it\/wp-json\/wp\/v2\/tags?post=2907"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}